Submissions from 2007
Heat transfer analysis in mechanical seals using fin theory, Z. Luan and M. M. Khonsari
An experimental investigation of dimple effect on the stribeck curve of journal bearings, Xiaobin Lu and M. M. Khonsari
An experimental investigation of grease-lubricated journal bearings, Xiaobin Lu and M. M. Khonsari
An experimental study of grease-lubricated journal bearings undergoing oscillatory motion, Xiaobin Lu and M. M. Khonsari
Thermal influence on torque transfer of wet clutches in limited slip differential applications, Pär Marklund, Rikard Mäki, Roland Larsson, Erik Höglund, M. M. Khonsari, and Joonyoung Jang
Eutectic bonding of Al-based high aspect ratio microscale structures, Fanghua Mei, J. Jiang, and W. J. Meng
Molecular dynamics simulation of pore growth in lipid bilayer membranes in the presence of edge-active agents, Dorel Moldovan, Dinesh Pinisetty, and Ram V. Devireddy
Mesoscale modelling of grain growth and microstructure in polycrystalline materials, D. Moldovan and D. Wolf
An optimal batch size for an imperfect production system with quality assurance and rework, D. Ojha, B. R. Sarker, and P. Biswas
Optimization of the geometry for continuous flow pcr devices in a titer plate-based pcr multi-reactor platform, D. S. Park, P. C. Chen, B. H. You, N. Kim, T. Park, P. Datta, Y. Desta, S. A. Soper, D. E. Nikitopoulos, and M. C. Murphy
UV-cured FRP joint thickness effect on coupled composite pipes, J.A. Peck, R.A. Jones, S.-S. Pang, G. Li, and B.H. Smith
Molecular dynamics simulation studies of pore formation in lipid bilayers in the presence of dimethylsulfoxide, Dinesh Pinisetty, Raghava Alapati, Dorel Moldovan, and Ram V. Devireddy
Supply chain models for an assembly system with preprocessing of raw materials, Mohammad Anwar Ashek Rahman and Bhaba R. Sarker
Materials Selection and Applications in Mechanical Engineering, Aravamudhan Raman
A quadra-directional decomposition heuristic for a two-dimensional, non-equidistant machine-cell location problem, Bhaba R. Sarker and Junfang Yu
Superadiabatic combustion in conducting tubes and heat exchangers of finite length, Ingmar Schoegl and Janet L. Ellzey
Photon-beam lithography reaches 12.5 nm half-pitch resolution, Harun H. Solak, Yasin Ekinci, Philipp Käser, and Sunggook Park
Stress analysis of non-conventional composite pipes, M. A. Wahab, M. S. Alam, S. S. Pang, J. A. Peck, and R. A. Jones
Analytical formulation for the temperature profile by Duhamel's theorem in bodies subjected to an oscillatory heat source, Jun Wen and M. M. Khonsari
Transient temperature involving oscillatory heat source with application in fretting contact, Jun Wen and M. M. Khonsari
Theory of slope-dependent disjoining pressure with application to Lennard-Jones liquid films, Taeil Yi and Harris Wong
Theory of slope-dependent disjoining pressure with application to Lennard-Jones liquid films, Taeil Yi and Harris Wong
Dimensional and locational integrity in the replication of polymeric microdevices, Byoung Hee You, Daniel S. Park, Pin Chuan Chen, Wilfredo M. Caceres, Dimitris E. Nikitopoulos, Steven A. Soper, and Michael C. Murphy
Fluid flow and heat transfer in a dual-wet micro heat pipe, J. Zhang, S. J. Watson, and H. Wong
Submissions from 2006
Temperature analysis of a gasket for an internal combustion engine, Dae Kyun Back and M. M. Khonsari
Fretting behavior of a rubber coating: Friction characteristics of rubber debris, Dae Kyun Baek and M. M. Khonsari
Reynolds equations for common generalized Newtonian models and an approximate Reynolds-Carreau equation, Scott Bair and M. M. Khonsari
An improved production plan to minimize machine idle time, Pablo Biswas and Bhaba R. Sarker
Materials Research Society Symposium Proceedings: Preface, Steve J. Bull, Paul R. Chalker, Shao Chen Chen, Wen Jin Meng, and Roya Maboudian
Fabrication of high-aspect-ratio microscale mold inserts by parallel μEDM, D. M. Cao, J. Jiang, R. Yang, and W. J. Meng
Development of a smart composite pipe joint integrated with piezoelectric layers under tensile loading, J. Cheng, X. Wu, G. Li, F. Taheri, and S.-S. Pang
Performance of an electrokinetic shuttle PCR polymerase Chain reactor, Pin Chuan Chen, Jifeng Chen, Dimitris E. Nikitopoulos, Steven A. Soper, and Michael C. Murphy
Optimal inventory policy for specialty chemical products in multiple packages, E. J. Comeaux and B. R. Sarker
Metal micromolding with surface engineered inserts, D. M. Cuo, J. Jiang, and W. J. Meng
Modeling and fabrication of a micro thermocouple array, A. Z. Cygan, A. Kardak, D. Patterson, E. J. Podhala-Murphy, R. V. Devireddy, and M. C. Murphy
Permeability characteristics of ovine primordial follicles calculated with two parameter Kedem-Katchalsky formulation, R. V. Devireddy, C. A. Amorim, and S. P. Leibo
Suprazero cooling conditions significantly influence subzero permeability parameters of mammalian ovarian tissue, R. V. Devireddy, G. Li, and S. P. Leibo
Finite horizon planning for a production system with permitted shortage and fixed-interval deliveries, Ahmad Diponegoro and Bhaba R. Sarker
A delta-function model for axially symmetric crystals, P. Du and H. Wong
Design aspects and simulations of a modified micro-scale electrophoretron, Nada Elmajdoub, Dimitris E. Nikitopoulos, Steven A. Soper, and Michael C. Murphy
Directional cooling of adult stem cells, R. Fuller and R. V. Devireddy
Theory and analysis of non-ideal detonation for RDX-metal mixtures, Keith A. Gonthier and Chad G. Rumchik
Investigation into three-layered HMA mixtures, B. Huang, G. Li, and X. Shu
High-precision micromilling for low-cost fabrication of metal mold masters, Mateusz L. Hupert, W. Jason Guy, Shawn D. Llopis, Catherine Situma, Sudheer Rani, Dimitris E. Nikitopoulos, and Steven A. Soper
On the role of enduring contact in powder lubrication, J. Y. Jang and M. M. Khonsari
Low velocity impact response and residual strength of composite sandwich structures with hybrid syntactic foam core, M. John and G. Li
Effect of contamination on the performance of hydrodynamic bearings, M. M. Khonsari and E. R. Booser
Proper film thickness key to bearing survival, M. M. Khonsari and E. R. Booser
Pulsing to improve bubble column performance: I. Low gas rates, F. Carl Knopf, Jia Ma, Richard G. Rice, and Dimitris Nikitopoulos
Identification of composite beam delamination parameters, S.G. Krishna, K.V. Singh, S.-S. Pang, and G. Li
Identification of composite beam delamination parameters, Srinivas Gopal Krishna, Kumar V. Singh, Su Seng Pang, and Guoqiang Li
Numerical solution of ocular fluid dynamics in a rabbit eye: parametric effects, Satish Kumar, Sumanta Acharya, Roger Beuerman, and Arto Palkama
Interfacial states and far-from-equilibrium transitions in the epitaxial growth and erosion on (110) crystal surfaces, Artem Levandovsky, Leonardo Golubović, and Dorel Moldovan
Experimental study of FRP confined concrete cylinders, G. Li
Fast repair of damaged RC beams using UV curing FRP composites, G. Li and A. Ghebreyesus
Effect of fiber orientation on the structural behavior of FRP wrapped concrete cylinders, G. Li, D. Maricherla, K. Singh, S.-S. Pang, and M. John
Effect of glycerol and cholesterol-loaded cyclodextrin on freezing-induced water loss in bovine spermatozoa, G. Li, J. Saenz, R. A. Godke, and R. V. Devireddy
Subzero water transport characteristics and optimal rates of freezing rhesus monkey (Macaca Mulatta) ovarian tissue, G. Li, S. Thirumala, S. P. Leibo, and R. V. Devireddy
Fusion and visualization of 3D image and elevation data in Computer Automated Virtual Environment (CAVE), X. Li, M.A. Stubblefield, G. Li, and H.D. Jerro
Numerical simulations of the flow field around the rings of mechanical seals, Zhaogao Luan and M. M. Khonsari
On the lift-off speed in journal bearings, Xiaobin Lu and Michael M. Khonsari
The Stribeck curve: Experimental results and theoretical prediction, Xiaobin Lu, M. M. Khonsari, and E. R.M. Gelinck
Grain-boundary grooving by surface diffusion with asymmetric and strongly anisotropic surface energies, Donghong Min and Harris Wong
Rayleigh's instability of Lennard-Jones liquid nanothreads simulated by molecular dynamics, Donghong Min and Harris Wong
The effect of strong surface energy anisotropy on migrating grain-boundary grooves, Donghong Min and Harris Wong
On active control of film-cooling flows, Dimitris E. Nikitopoulos, Jeremiah Oertling, Sumanta Acharya, and Frank H. Muldoon
Microtiter plate-based microfluidic platforms: Sealing, leakage testing, and performance of a 96-well SPRI device, D. S. Park, M. Hupert, J. Guy, P. Datta, J. B. Lee, M. Witek, B. H. You, S. A. Soper, D. E. Nikitopoulos, and M. C. Murphy
A thermohydrodynamic analysis of foil journal bearings, Z. C. Peng and M. M. Khonsari
The effect of methanol on lipid bilayers: An atomistic investigation, D. Pinisetty, D. Moldovan, and R. Devireddy
Simulation of electroosmotic and pressure driven flows in microfluidic interconnects, Sudheer D. Rani, Steven A. Soper, Dimitris E. Nikitopoulos, and Michael C. Murphy
Erratum to "Optimal ordering policies in response to discount offer" [International Journal of Production Economics 100 (2006) 195-211] (DOI:10.1016/j.ijpe.2004.10.015), Bhaba R. Sarker and Mahmood Al Kindi
Optimal ordering policies in response to a discount offer, Bhaba R. Sarker and Mahmood Al Kindi
Method of regulating or controlling a cyclically operating internal combustion engine, Ingmar Schoegl
Mass/heat transfer in rotating, smooth, high-aspect ratio (4:1) coolant channels with curved walls, Eashwar Sethuraman, Dimitris E. Nikitopoulos, and Sumanta Acharya
Semantic image retrieval based on probabilistic latent semantic analysis, Amin Shah-Hosseini and Gerald M. Knapp
Free vibration and physical parameter identification of non-uniform composite beams, K.V. Singh, G. Li, and S.-S. Pang
Analysis of heat partitioning in wheel/rail and wheel/brake shoe friction contact: An analytical approach, A. Tudor and M. Khonsari
Effect of pressure suit on functional reach, Nageswara Rao Uppu, Fereydoun Aghazadeh, and Larry Nabatilan
Experimental and numerical simulation of restraining forces in gas metal arc welded joints, M. A. Wahab, M. S. Alam, M. J. Painter, and P. E. Stafford
Effect of corrosion prevention compounds on fatigue life in 2024-T3 aluminum alloy, M. A. Wahab, J. H. Park, M. S. Alam, and S. S. Pang
A new derivation for journal bearing stiffness and damping coefficients in polar coordinates, J. K. Wang and M. M. Khonsari
Application of Hopf bifurcation theory to rotor-bearing systems with consideration of turbulent effects, J. K. Wang and M. M. Khonsari
Bifurcation analysis of a flexible rotor supported by two fluid-film journal bearings, J. K. Wang and M. M. Khonsari
Influence of Inlet Oil Temperature on the Instability Threshold of Rotor-Bearing Systems, J. K. Wang and M. M. Khonsari
Influence of inlet oil temperature on the instability threshold of rotor-bearing systems, J. K. Wang and M. M. Khonsari
On the hysteresis phenomenon associated with instability of rotor-bearing systems, J. K. Wang and M. M. Khonsari
Prediction of the stability envelope of rotor-bearing system, J. K. Wang and M. M. Khonsari
Evaluation of critical design factors on tfhe thermal behavior due to frictional heat in the oscillatory sliding conformal contact, P. Wang, D. Y. Hua, M. Mansouri, and M. M. Khonsari
Optimal models for a multi-stage supply chain system controlled by kanban under just-in-time philosophy, Shaojun Wang and Bhaba R. Sarker
Relation between grain growth and grain-boundary diffusion in a pure material by molecular dynamics simulations, V. Yamakov, D. Moldovan, K. Rastogi, and D. Wolf
Numerical simulation and fabrication of microscale, multilevel, tapered mold inserts using UV-Lithographie, Galvanoformung, Abformung (LIGA) technology, Ren Yang, J. Jiang, W. J. Meng, and Wanjun Wang
Passive alignment structures in modular, polymer microfluidic devices, Byoung Hee You, Pin Chuan Chen, Jason Guy, Proyag Datta, Dimitris E. Nikitopoulos, Steven A. Soper, and Michael C. Murphy
Tolerance variation and passive alignment in modular, polymer microfluidic devices, Byoung Hee You, Daniel S. Park, Christipher W. Mock, Wilfredo M. Caceres, Dimitris E. Nikitopoulos, Steven A. Soper, and Michael C. Murphy
A directional decomposition heuristic for one-dimensional, non-equidistant machine-cell location problems, Junfang Yu and Bhaba R. Sarker
Submissions from 2005
A new approach for modeling of fatigue crack growth in welded cruciform and curve T joint structures, Mohammad S. Alam and Muhammad A. Wahab
Finite element modeling of fatigue crack growth in curved-welded joints using interface elements, M. S. Alam and M. A. Wahab
Modeling the fatigue crack growth and propagation life of a joint of two elastic materials using interface elements, M. S. Alam and M. A. Wahab
Friction and wear of a rubber coating in fretting, Dae Kyun Baek and M. M. Khonsari
Generalized Reynolds equations for line contact with double-Newtonian shear-thinning, Scott Bair and M. M. Khonsari
Reynolds equations for common generalized newtonian models and an approximate Reynolds-Carreau equation, Scott Bair and M. M. Khonsari